×

74AVC16244DGG

16-bit buffer/line driver; 3.6 V tolerant; 3-state

The 74AVC16244 is a 16-bit non-inverting buffer/line driver with 3-state outputs. This device can be used as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer. The 3‑state outputs are controlled by the output enable inputs nOE. A HIGH level on input nOE causes the outputs to assume a high-impedance OFF-state.

The 74AVC16244 is designed to have an extremely fast propagation delay and a minimum amount of power consumption.

To ensure the high-impedance output state during power-up or power-down, input nOE should be tied to VCC through a pull-up resistor (Live Insertion).

A dynamic controlled output (DCO) circuitry is implemented to support termination line drive during transient.

This product has been discontinued, click here for discontinuation information and replacement parts.

Features and benefits

  • Wide supply voltage range from 1.2 V to 3.6 V

  • Complies with JEDEC standards:

    • JESD8-7 (1.2 V to 1.95 V)

    • JESD8-5 (1.8 V to 2.7 V)

    • JESD8-1A (2.7 V to 3.6 V)

  • CMOS low power consumption

  • Input/output tolerant up to 3.6 V

  • Dynamic Controlled Output (DCO) circuit dynamically changes output impedance, resulting in noise reduction without speed degradation

  • Low inductance multiple VCC and GND pins to minimize noise and ground bounce

  • Supports Live Insertion

Applications

Parametrics

Type number Product status VCC (V) Logic switching levels Output drive capability (mA) fmax (MHz) Nr of bits Power dissipation considerations Rth(j-a) (K/W) Rth(j-c) (K/W) Package name
74AVC16244DGG End of life 0.8 - 3.6 CMOS/LVTTL ± 12 200 16 very low 82 37 TSSOP48

PCB Symbol, Footprint and 3D Model

Model Name Description

Package

All type numbers in the table below are discontinued. See the table Discontinuation information for more information.

Type number Orderable part number, (Ordering code (12NC)) Status Marking Package Package information Reflow-/Wave soldering Packing
74AVC16244DGG 74AVC16244DGG,118
(935264443118)
Withdrawn / End-of-life AVC16244 SOT362-1
TSSOP48
(SOT362-1)
SOT362-1 SSOP-TSSOP-VSO-WAVE
SOT362-1_118
74AVC16244DGG,112
(935264443112)
Obsolete AVC16244 Not available
74AVC16244DGG,512
(935264443512)
Obsolete AVC16244 Not available
74AVC16244DGG,518
(935264443518)
Obsolete AVC16244 Not available

Environmental information

All type numbers in the table below are discontinued. See the table Discontinuation information for more information.

Type number Orderable part number Chemical content RoHS RHF-indicator
74AVC16244DGG 74AVC16244DGG,118 74AVC16244DGG rohs rhf rhf
74AVC16244DGG 74AVC16244DGG,112 74AVC16244DGG rohs rhf rhf
74AVC16244DGG 74AVC16244DGG,512 74AVC16244DGG rohs rhf rhf
74AVC16244DGG 74AVC16244DGG,518 74AVC16244DGG rohs rhf rhf
Quality and reliability disclaimer

Documentation (8)

File name Title Type Date
74AVC16244 16-bit buffer/line driver; 3.6 V tolerant; 3-state Data sheet 2018-02-20
AN90007 Pin FMEA for AVC family Application note 2018-11-30
SOT362-1 3D model for products with SOT362-1 package Design support 2020-01-22
avc16244 avc16244 IBIS model IBIS model 2013-04-07
Nexperia_package_poster Nexperia package poster Leaflet 2020-05-15
TSSOP48_SOT362-1_mk plastic, thin shrink small outline package; 48 leads; 0.5 mm pitch; 12.8 mm x 6.1 mm x 1.2 mm body Marcom graphics 2017-01-28
SOT362-1 plastic thin shrink small outline package; 48 leads; body width 6.1 mm Package information 2024-01-05
SSOP-TSSOP-VSO-WAVE Footprint for wave soldering Wave soldering 2009-10-08

Support

If you are in need of design/technical support, let us know and fill in the answer form we'll get back to you shortly.

Models

File name Title Type Date
avc16244 avc16244 IBIS model IBIS model 2013-04-07
SOT362-1 3D model for products with SOT362-1 package Design support 2020-01-22

PCB Symbol, Footprint and 3D Model

Model Name Description

How does it work?

The interactive datasheets are based on the Nexperia MOSFET precision electrothermal models. With our interactive datasheets you can simply specify your own conditions interactively. Start by changing the values of the conditions. You can do this by using the sliders in the condition fields. By dragging the sliders you will see how the MOSFET will perform at the new conditions set.